본문 바로가기

회사일

TS 23.501 f20 5.17절 번역 (5GC : interworking with EPC)

구글 번역이 꽤 잘 하지만 아직은 사람의 손길이 필요하다...


5G Seminar - 23.501 15.17.pptx

23501-f20-5.17절번역.doc

5.17      Interworking and Migration

5.17.1     Support for Migration from EPC to 5GC

5.17.1.1        General

Clause 5.17.1 describes the UE and network behaviour for the migration from EPC to 5GC.

Deployments based on different 3GPP architecture options (i.e. EPC based or 5GC based) and UEs with different capabilities (EPC NAS and 5GC NAS) may coexist at the same time within one PLMN.

It is assumed that a UE that is capable of supporting 5GC NAS procedures may also be capable of supporting EPC NAS (i.e. the NAS procedures defined in TS 24.301 [13]) to operate in legacy networks


e.g. in the case of roaming.

The UE will use EPC NAS or 5GC NAS procedures depending on the core network by which it is served.

In order to support smooth migration, it is assumed that the EPC and the 5GC have access to a common subscriber database, that is HSS in the case of EPC and the UDM in the case of 5GC, acting as the master data base for a given user as defined in TS 23.002 [21].




Figure 5.17.1.1-1: Architecture for migration scenario for EPC and 5G CN

A UE that supports only EPC based Dual Connectivity with secondary RAT NR:

-    always performs initial access through E-UTRA (LTE-Uu) but never through NR;

-    performs EPC NAS procedures over E-UTRA (i.e. Mobility Management, Session Management etc) as defined in TS 24.301 [13].

A UE that supports camping on 5G Systems with 5GC NAS:

-    performs initial access either through E-UTRAN that connects to 5GC or NR towards 5GC;

-    performs initial access through E-UTRAN towards EPC, if supported and needed;

-    performs EPC NAS or 5GC NAS procedures over E-UTRAN or NR respectively (i.e. Mobility Management, Session Management etc) depending on whether the UE requests 5GC access or EPC access, if the UE also supports EPC NAS.

When camping on an E-UTRA cell connected to both EPC and 5GC, a UE supporting EPC NAS and 5GC NAS shall select a core network type (EPC or 5GC) and initiate the corresponding NAS procedure as specified in TS 23.122 [17].

In order to support different UEs with different capabilities in the same network, i.e. both UEs that are capable of only EPC NAS (possibly including EPC based Dual Connectivity with secondary NR) and UEs that support 5GC NAS procedures in the same network:

-    eNB that supports access to 5GC shall broadcast that it can connect to 5GC. Based on that, the UE AS layer indicates "E-UTRA connected to 5GC" capability to the UE NAS layer.

-    It is also expected that the UE AS layer is made aware by the UE NAS layer whether a NAS signalling connection is to be initiated to the 5GC. Based on that, UE AS layer indicates to the RAN whether it is requesting 5GC access (i.e. "5GC requested" indication). The RAN uses this indication to determine whether a UE is requesting 5GC access or an EPC access. RAN routes NAS signalling to the applicable AMF or MME accordingly.

NOTE:     The UE that supports EPC based Dual Connectivity with secondary RAT only does not provide this "5GC requested" indication at Access Stratum when it performs initial access and therefore eNB uses the "default" CN selection mechanism to direct this UE to an MME

Based on the Core Network type restriction (e.g. due to lack of roaming agreements) described in clause 5.3.4.1.1 (i.e. based on Registration Reject) the 5GC network may steer the UE towards EPC.

In this Release of the specification there is no support in 5G System for some functionalities supported in EPS such as ProSe, MBMS, CIOT optimisations, V2X etc. The UE that wants to use one or more of these functionalities not supported by 5G System, when in CM-IDLE may disable all the related radio capabilities that allow the UE to access 5G System. The triggers to disable and re-enable the 5GS capabilities to access 5G System in this case are left up to UE implementation.

5.17.1.2        User Plane management to support interworking with EPS

In order to support the interworking with EPC, the SMF+PGW-C provides information over N4 to the UPF+PGW-U related to the handling of traffic over S5-U. Functionality defined in TS 23.503 [45] for traffic steering control on SGi-LAN/N6 can be activated in UPF+PGW-U under consideration of whether the UE is connected to EPC or 5GC.

When the UE is connected to EPC and establishes/releases PDN connections, the following differences apply to N4 compared to when the UE is connected to 5GC:

-    If the network is configured to perform allocation/release of CN Tunnel Info in the SMF+PGW-C, the SMF+PGW-C shall allocate/release CN Tunnel Info for each EPS Bearer.

-    If the network is configured to perform allocation/release of CN Tunnel Info in the UPF, the SMF+PGW-C shall request UPF+PWG-U to allocate/release CN Tunnel Info for each EPS Bearer.

-    In addition to the Service Data Flow related information, the SMF+PGW-C shall be able to provide the GBR and MBR values for each GBR bearer of the PDN connection to the UPF+PGW-U.

5.17.2     Interworking with EPC

5.17.2.1        General

Interworking with EPC in this clause refers to mobility procedures between 5GC and EPC/E-UTRAN, except for subclause 5.17.2.4.

In order to interwork with EPC, the UE that supports both 5GC and EPC NAS can operate in single-registration mode or dual-registration mode:

-    In single-registration mode, UE has only one active MM state (either RM state in 5GC or EMM state in EPC) and it is either in 5GC NAS mode or in EPC NAS mode (when connected to 5GC or EPC, respectively). UE maintains a single coordinated registration for 5GC and EPC. Accordingly, the UE maps the EPS-GUTI to 5G GUTI during mobility between EPC and 5GC and vice versa following the mapping rules in Annex B. To enable re-use of a previously established 5G security context when returning to 5GC, the UE also keeps the native 5G-GUTI and the native 5G security context when moving from 5GC to EPC.

-    In dual-registration mode, UE handles independent registrations for 5GC and EPC using separate RRC connections. In this mode, UE maintains 5G-GUTI and EPS-GUTI independently. In this mode, UE provides native 5G-GUTI, if previously allocated by 5GC, for registrations towards 5GC and it provides native EPS-GUTI, if previously allocated by EPC, for Attach/TAU towards EPC. In this mode, the UE may be registered to 5GC only, EPC only, or to both 5GC and EPC.

     Dual-registration mode is intended for interworking between EPS/E-UTRAN and 5GS/NR. A dual-registered UE should not send its E-UTRA capability to NR access when connected to 5GS/NR to avoid being handed over to 5GC-connected E-UTRA.

NOTE 1:  This is to prevent the UE from being connected to E-UTRAN/EPC and E-UTRA/5GC simultaneously using separate RRC connections via single RAN node as a result of handover. If a dual- registered UE implementation chooses to send its E-UTRA capability when connected to 5GS/NR, the UE and the network behaviour when UE enters a 5GC-connected E-UTRA is not further specified. If however the UE is registered with 5GS/NR only, the UE can send its E-UTRA capability in order to allow inter-RAT handover to E-UTRA/5GC and Dual Connectivity with multiple RATs.

The support of single registration mode is mandatory for UEs that support both 5GC and EPC NAS.

5GC EPC NAS 를 모두 지원하는 UE에게 단일 접속 모드의 지원은 필수적이다.

During E-UTRAN Initial Attach, UE supporting both 5GC and EPC NAS shall indicate its support of 5G NAS in UE Network Capability described in clause 5.11.3 of TS 23.401 [26].

E-UTRAN 초기 접속 (initial attach) , 5GC EPC NAS를 모두 지원하는 UE TS 23.401 5.11.3 [26]에 설명된 것과 같이, UE Network Capability 5G NAS에 대한 지원 여부를 명시적으로 알려줘야 한다.

During registration to 5GC, UE supporting both 5GC and EPC NAS shall indicate its support of EPC NAS.

5GC에 등록하는 동안, 5GC EPC NAS를 모두 지원하는 UE EPC NAS에 대한 지원을 명시적으로 알려줘야 한다.

NOTE 2:  This indication may be used to give the priority towards selection of PGW-C + SMF for UEs that support both EPC and 5GC NAS.

2: indication EPC 5GC NAS 를 모두 지원하는 UE를 위한 PGW-C + SMF 선택에 우선순위를 부여하기 위해 사용될 수 있다.

PDU Session types "Ethernet" and "Unstructured" are transferred to EPC as "non-IP" PDN type (when supported by UE and network). UE sets the PDN type to non-IP when it moves from 5GS to EPS and after the transfer to EPS, the UE and the SMF shall maintain information about the PDU Session type used in 5GS, i.e. information indicating that the PDN Connection with "non-IP" PDN type corresponds to PDU Session type Ethernet or Unstructured respectively. This is done to ensure that the appropriate PDU Session type will be used if the UE transfers to 5GS.

PDU Session 유형 “Ethernet” “Unstructured” EPC “non-IP” PDN type 으로 전송된다. (단말과 네트워크에서 지원할 경우) UE5GS 에서 EPS로 이동할 때 PDN 유형을 “non-IP” 로 설정하며, EPS 로 이동한 뒤 UESMF5GS 에서 사용됐던 PDU Session type을 따로 기록해두도록 한다. (Ethernet 인지 Unstructured 인지.) 이는 이후 UE5GS 로 넘어갈 때 적합한 PDU session type 을 다시 사용하는 것이 보장되도록 하기 위함이다.

 

It is assumed that if a UE supports Ethernet PDU Session type and/or Unstructured PDU Session type in 5GS it will also support non-IP PDN type in EPS. If this is not the case, the UE shall locally delete any EBI(s) corresponding to the Ethernet/Unstructured PDU Session(s) to avoid that the Ethernet/Unstructured PDU Session(s) are transferred to EPS.

UE5GS에서 Ethernet PDU Session type 이나 Unstructured PDU Session type을 지원한다면, EPS에서 non-IP PDN type 역시 지원할 것으로 가정한다. 그렇지 않은 경우, UEEthernet/Unstructured PDU Session EPS 로 전송되는 것을 피하기 위해 Ethernet/Unstructured PDU Session에 해당하는 EBI 를 로컬로 삭제해야 한다.

Networks that support interworking with EPC, may support interworking procedures that use the N26 interface or interworking procedures that do not use the N26 interface. Interworking procedures with N26 support provides IP address continuity on inter-system mobility to UEs that support 5GC NAS and EPC NAS and that operate in single registration mode. Networks that support interworking procedures without N26 shall support procedures to provide IP address continuity on inter-system mobility to UEs operating in both single-registration mode and dual-registration mode. In such networks, AMF shall provide the indication that interworking without N26 is supported to UEs during initial Registration in 5GC or MME may optionally provide the indication that interworking without N26 is supported in the Attach procedure in EPC as defined in TS 23.401 [26].

EPC 와의 연동을 지원하는 네트워크는 N26 인터페이스를 쓰거나 쓰지 않는 방식으로 연동 절차를 지원할 수 있다. N26 을 사용하는 연동 절차는 5GC NAS EPC NAS를 지원하고 단일 등록 모드에서 작동하는 UE시스템 간 이동 중 IP 주소 연속성을 제공합니다. N26미사용 연동 절차를 지원하는 네트워크는 단일 등록 모드와 이중 등록 모드 모두에서 작동하는 UE시스템 간 이동 중 IP 주소 연속성을 제공하는 절차를 지원해야합니다. 이러한 네트워크에서, AMF N26을 미 사용하는 연동 동작이 지원된다는 사실을 UE에게 5GC로의 초기 등록 중 알려주어야만 하며MME TS 23.401 [26] 에서 정의된 EPC에서의 Attach 절차에 따라 선택적으로 N26 미 사용 연동 동작이 지원되는지 여부를 알려줄 수 있다.

In entire clause 5.17.2 the terms "initial attach", "handover attach" and "TAU" for the UE procedures in EPC can alternatively be combined EPS/IMSI Attach and combined TA/LA depending on the UE configuration defined in TS 23.221 [23].

5.17.2 절 전체에서 EPC UE 단위 "초기 attach", "handover attach" "TAU"라는 용어는 TS 23.221[23] 에 정의된 UE의 구성에 따라 EPS / IMSI Attach Combined TA/LA 와 복합적으로 사용될 수 있다.

If a UE in MICO mode moves to E-UTRAN connected to EPC and any of the triggers defined in clause 5.4.1.3 occur, then the UE shall locally disable MICO mode and perform the TAU or Attach procedure as defined in clause 5.17.2. The UE can renegotiate MICO when it returns to 5GS during (re-)registration procedure.

MICO 모드의 UE EPC에 연결된 E-UTRAN으로 이동할 때 5.4.1.3 절에 정의 된 트리거가 발생하면, UE MICO 모드를 국지적으로 비활성화하고 5.17.2 절에 정의된 TAU 또는 Attach 절차를 수행해야 한다. UE()등록 과정에서 5GS로 복귀 할 때 MICO를 재협상 할 수있다.

IP address preservation for IP PDU sessions cannot be ensured on subsequent mobility from EPC/E-UTRAN to GERAN/UTRAN to a UE that had initially registered in 5GS and moved to EPC/E-UTRAN.

IP PDU 세션에 대한 IP 주소 유지 동작은 5GS에 처음 등록 EPC/E-UTRAN으로 이동한 UE가 이후 EPC/E-UTRAN 에서 GERAN/UTRAN으로 후속 이동하는 경우에 대해서는 보장될 수 없다.

NOTE 3:  The SMF+PGW-C might not include the GERAN/UTRAN PDP Context anchor functionality. Also, 5GC does not provide GERAN/UTRAN PDP Context parameters to the UE when QoS flows of PDU Session are setup or modified in 5GS. Hence, the UE might not be able to activate the PDP contexts when it transitions to GERAN/UTRAN.

3 : SMF + PGW-C GERAN/UTRAN PDP Context anchor 기능을 포함하지 않을 수도 있다. 또한, 5GC PDU 세션의 QoS 흐름이 5GS에서 설정되거나 변경되는 경우 UE GERAN / UTRAN PDP Context 파라미터를 제공하지 않는다. 따라서, UE GERAN / UTRAN으로 천이 할 때 PDP 콘텍스트를 활성화하지 못할 수도 있다.

IP address preservation for IP PDU sessions cannot be ensured on subsequent mobility from EPC/E-UTRAN to 5GS to a 5GS NAS capable UE that had initially attached via GERAN/UTRAN and moved to EPC/E-UTRAN.

IP PDU 세션에 대한 IP 주소 유지 동작GERAN / UTRAN을 통해 초기 접속한 뒤 EPC / E-UTRAN으로 이동한 5GS NAS 가능 UE 이후 EPC/E-UTRAN 에서 5GS 후속 이동하는 경우에 대해서는 보장될 수 없다.

NOTE 4:  The SMF+PGW-C might not include the GERAN/UTRAN PDP Context anchor functionality. Also, 5GS NAS capable UE does not indicate the support of this capability to the network during GPRS attach via GERAN/UTRAN. Hence, SMF+PGW-C might not be selected for the UE's PDP contexts that are setup in GERAN/UTRAN.

4 : SMF + PGW-C GERAN / UTRAN PDP Context anchor 기능을 포함하지 않을 수도 있다. 또한, 5GS NAS 지원 가능 UE GERAN / UTRAN을 통해 GPRS attach 중에 중에 이 기능에 대한 지원 여부를 네트워크에 알려주지 않는다. 따라서, GERAN / UTRAN에서 셋업 UE PDP 콘텍스트에 대해 SMF + PGW-C가 선택되지 않을 수있다.

5.17.2.2        Interworking Procedures with N26 interface

5.17.2.2.1            General

Interworking procedures using the N26 interface, enables the exchange of MM and SM states between the source and target network. When interworking procedures with N26 is used, the UE operates in single-registration mode. For the 3GPP access, the network keeps only one valid MM state for the UE, either in the AMF or MME. For the 3GPP access, either the AMF or the MME is registered in the HSS+UDM.

N26 인터페이스를 사용하는 연동 절차는 소스 및 대상 네트워크간에 MM SM 상태를 교환 할 수 있게 한다. N26을 사용하는 연동 절차에서, UE는 단일 등록 모드로 동작한다. 3GPP 액세스망에서, 네트워크는 AMF 또는 MME 에 하나의 UE에 대한 하나의 유효한 MM 상태만을 유지한다. 3GPP 액세스망에서, AMF 또는 MME HSS + UDM에 등록된다.

The support for N26 interface between AMF in 5GC and MME in EPC is required to enable seamless session continuity (e.g. for voice services) for inter-system change.

시스템 간 변경 시 끊김없는 세션 연속성 ( : 음성 서비스)을 가능하게 하려면, 5GC AMF EPC MME 간에 N26 인터페이스 지원이 필요하다.

When the UE moves from 5GS to EPS, the SMF determines which PDU Sessions can be relocated to the target EPS, e.g. based on capability of the deployed EPS, operator policies for which PDU Session, seamless session continuity should be supported etc. The SMF can release the PDU Sessions that cannot be transferred as part of the handover or Idle mode mobility. However, whether the PDU Session is successfully moved to the target network is determined by target EPS.

UE 5GS에서 EPS로 이동할 때, SMF는 어떤 PDU 세션들이 target EPS로 재배치(relocation) 될 수 있는지에 대해 다음 항목을 기반으로 결정한다. ( : 설정된 EPS capability, 어떤 PDU 세션을 쓸지, 끊김없는 세션 연속성을 지원해야하는지에 대한 운영자 정책 등) SMFhandover 또는 idle mode mobility의 일부로 전송할 수 없는 PDU 세션을 해제 할 수 있다. 하지만, PDU 세션이 target 네트워크로 성공적으로 이동되었는지 여부는 target EPS에 의해 결정된다.

Similarly, when the UE moves from EPS to 5GS, for the case when the MME has selected P-GW+SMF even for PDN connections that cannot be relocated to the target 5GS, the P-GW+SMF determines which PDN Connections can be relocated to the target 5GS, e.g. based on capability of the deployed 5GS, subscription and operator policies for which PDN Connection, seamless session continuity should be supported etc. The P-GW+SMF and NG-RAN can reject the PDN Connections that cannot be transferred as part of the handover or Idle mode mobility.

마찬가지로, UE EPS로부터 5GS로 이동하는 경우, MME가 타겟 5GS로 재배치 될 수 없는 PDN 접속에 대해서도 P-GW+SMF를 선택한 경우, P-GW+SMF는 어느 PDN 접속이 target 5GS 로 재배치(relocation) 될 수 있는지에 대해 다음 항목을 기반으로 결정한다. (: 배포된 5GS capability, 어떤 PDN Connection이나 끊김없는 세션 연속성이 지원되어야 하는지에 대한 구독 및 운용자 정책 등) P-GW+SGW NG-RAN Handover idle mode mobility 의 일부로 전송할 수 없는 PDU Connection 을 거부할 수 있다.

 

NOTE:     When applying the AMF planned removal procedure or the procedure to handle AMF failures (see clause 5.21.2) implementations are expected to update the DNS configuration to enable MMEs to discover alternative AMFs if the MME tries to retrieve a UE context from an AMF that has been taken out of service or has failed. This addresses the scenario of UEs performing 5GS to EPS Idle mode mobility and presenting a mapped GUTI pointing to an AMF that has been taken out of service or has failed.

: AMF 계획된 제거 절차 (AMF 를 계획된 시점에 제거하는건가?) AMF 오동작 처리 절차 (5.21.2 절 참조)를 적용 할 때, MME이미 서비스가 중단됐거나 오동작하는AMF에서 UE Context 를 얻어오려고 할 경우 대체 AMF를 검색 할 수 있도록 DNS 구성을 업데이트하는 구현이 필요할 수 있다. 이러한 시나리오는 UE5GS에서 EPSidle mode mobility 동작 수행 중, 서비스를 중단하거나 오동작하는 AMF를 가리키는 매핑 된 GUTI이용하는 경우에 적용된다.

5.17.2.2.2                 Mobility for UEs in single-registration mode

When the UE supports single-registration mode and network supports interworking procedure with the N26 interface:

UE가 단일 등록 모드를 지원하고 네트워크가 N26 인터페이스와의 연동 절차를 지원할 때 :

-    For idle mode mobility from 5GS to EPS, the UE performs either TAU or Attach procedure with EPS GUTI mapped from 5G-GUTI sent as old Native GUTI, as described in clause 4.11.1.3.2.1 of TS 23.502 [3] and indicates that it is moving from 5GC. The MME retrieves the UE's MM and SM context from 5GC. For connected mode mobility from 5GS to EPS, either inter-system handover or RRC Connection Release with Redirection to E-UTRAN is performed. At inter-system handover, the AMF selects target MME based on 2 octet TAC format used in the Target ID as specified in TS 38.413 [34]. During the TAU or Attach procedure the HSS+UDM cancels any AMF registration associated with the 3GPP access (but not AMF registration associated with the non-3GPP access): an AMF that was serving the UE over both 3GPP and non-3GPP accesses does not consider the UE as deregistered over non 3GPP access.

- 5GS에서 EPS 로의 idle mode mobility 위해, UE TS 23.502 4.11.1.3.2.1 [3]에 설명된 바와 같이 old Native GUTI로서 전송된 5G-GUTI에서 매핑된 EPS GUTI TAU 또는 Attach 절차를 수행하, 5GC에서 이동하고 있음을 알려준다. MME 5GC로부터 UE MM SM 컨텍스트를 획득한다. 5GS에서 EPS 로의 connected mode mobility 의 경우, 시스템 간 핸드 오버 또는 E-UTRAN으로의 리다이렉트를 갖는 RRC 접속 해제가 수행된다. 시스템 간 핸드 오버 , AMF TS 38.413 [34]에 명시된대로 Target ID에 사용된 2 octet TAC 포맷에 기반하여 target MME를 선택한다. TAU 또는 Attach 절차 동안 HSS+UDM 3GPP 액세스와 관련된 AMF 등록을 취소한다. (non-3GPP 액세스와 관련된 AMF 등록은 제외) : 3GPP non-3GPP 액세스 둘 다를 통해 UE를 서비스하 AMF UEnon-3GPP 액세스를 통해 등록 해제 된 것으로 간주한다.

-    For the first TAU after 5GC initial Registration, the UE and MME for the handling of UE Radio Capabilities follow the procedures as defined in TS 23.401 [26] clause 5.11.2 for first TAU after GERAN/UTRAN Attach.

- 5GC 초기 등록 후 첫 번째 TAU, UE MMETS 23.401 [26]5.11.2 절에 정의된 GERAN/UTRAN Attach 후 첫 번째 TAU절차를 따라 UE Radio Capability 를 다루도록 한다.

NOTE 1:  MMEs supporting interworking with N26 interface are not required to process the indication from the UE that it is moving from 5GC and will assume that the UE is moving from another MME.

1 : N26 인터페이스를 통한 연동을 지원하는 MMEUE5GC로부터 이동하고 있다는 정보를 처리할 필요가 없으며, UE가 다른 MME로부터 이동하고 있다고 가정하도록 한다.

-    For idle mode mobility from EPC to 5GC, the UE performs mobility Registration procedure with the 5G GUTI mapped from EPS GUTI and indicates that it is moving from EPC. The UE derives GUAMI from the native 5G-GUTI and includes GUAMI in the RRC message to enable RAN to route to the corresponding AMF (if available). The AMF and SMF retrieve the UE's MM and SM context from EPC. For connected mode mobility from EPC to 5GC, either inter-system handover or RRC Connection Release with Redirection to NG-RAN is performed. At inter-system handover, the MME selects target AMF based on 3 octet TAC format used in the Target ID as specified in TS 38.413 [34]. During the Registration procedure, the HSS+UDM cancels any MME registration.

- EPC에서 5GC 로의 idle mode mobility , UE EPS GUTI로부터 매핑된 5G GUTI로 이동성 등록 절차를 수행하고 EPC로부터 이동 중임을 나타낸다. UE는 고유한 5G-GUTI로부터 GUAMI를 도출하고, RRC 메시지에 GUAMI를 포함하여 (가능한 경우) RAN이 대응하는 AMF로 라우팅 할 수 있게 한다. AMF SMF EPC로부터 UE MM SM 컨텍스트를 획득한다. EPC에서 5GC connected mode mobility , 시스템 간 핸드 오버 또는 NG-RAN 으로의 리다이렉션을 통한 RRC 연결 해제가 수행됩니다. 시스템 간 핸드 오버 , MME TS 38.413 [34]에 명시된대로 Target ID에 사용된 3 octet TAC 형식에 기반하여target AMF를 선택한다. 등록 절차 , HSS+UDM어떤 MME 등록 (요청)도 모두 취소합니다.

For both idle mode and connected mode mobility from EPC to 5GC:

EPC에서 5GC로의 Idle mode connected mode mobility 모두에 대해:

-    The UE includes the native 5G-GUTI as an additional GUTI in the Registration request; the AMF uses the native 5G-GUTI to retrieve MM context identified by the 5G-GUTI from old AMF or from UDSF (if UDSF is deployed and the old AMF is within the same AMF set).

- UEadditional GUT 고유 5G-GUTI등록 요청(메시지)함한다. AMF는 고유한 5G-GUTI를 사용하여 이전 AMF 또는 UDSF (UDSF가 배포되고 이전 AMF가 동일한 AMF 집합 내에 있는 경우)에서 5G-GUTI에 의해 식별되는 MM 컨텍스트를 획득합니다.

-    If the UE supports Reflective QoS functionality and if this is the first mobility event for a PDU Session that was established while being connected to EPC, the UE shall trigger the PDU Session Modification procedure and should indicate the support of Reflective QoS to the network (i.e. SMF). If the UE indicated support of Reflective QoS, the network may provide a Reflective QoS Timer (RQ Timer) value to the UE .

- UE Reflective QoS 기능을 지원하고 이것이 EPC에 연결되어 있는 동안 설정된 PDU Session에 대한 첫 번째 mobility 이벤트인 경우, UE PDU 세션 수정 절차를 트리거해야 하며 Reflective QoS지원 가능하다고 네트워크(: SMF)알려줘야 한다. UEReflective QoS를 지원한다고 하는 경우, 네트워크는 Reflective QoS 타이머 (RQ Timer) 값을 UE 제공할 수 있다.

5.17.2.3        Interworking Procedures without N26 interface

5.17.2.3.1            General

For interworking without the N26 interface, IP address preservation is provided to the UEs on inter-system mobility by storing and fetching PGW-C+SMF and corresponding APN/DDN information via the HSS+UDM. In such networks AMF also provide an indication that interworking without N26 is supported to UEs during Initial Registration in 5GC or MME may optionally provide an indication that interworking without N26 is supported in the Attach procedure in EPC as defined in TS 23.401 [26]. The UE provides an indication that it supports Request Type flag "handover" for PDN connectivity request during the attach procedure as described in clause 5.3.2.1 of TS 23.401 [26] and during initial Registration and mobility Registration Update in 5GC.

N26 인터페이스를 미 사용하는 상호 연동, HSS+UDM을 통해 PGW-C+SMF 이에 대응하는 APN/DDN 정보를 저장하고 인출하여 시스템 간 이동 중 단말의 IP 주소가 유지되도록 한다. 이러한 네트워크에서 AMF는 또한 단말이 5GC로 초기 등록하는 동안 N26을 미 사용하는 연동 동작이 지원된다고 알려주고, MME도 선택적으로 (필요 시 부가적으로?) N26을 미 사용하는 연동 동작이 지원됨을 TS 23.401 [26]에서 정의된 대로 EPCAttach 절차 중 알려줄 수 있다. UE TS 23.401 5.3.2.1 [26]에 기술된 attach 절차 5GC로의 초기 등록과 이동성 등록 갱신 절차 중 수행하는 PDN 연결 요청에 Request Type 플래그 “handover” 를 지원한다는 표시를 제공한다.

NOTE 1:  The UE support of Request Type flag "handover" for PDN connectivity request during the attach procedure is needed for IP address preservation in the case of interworking without N26.

1 : N26을 미 사용하는 상호 연동 시 IP 주소를 유지하기 위해서는 단말이 attach 절차 중  PDN 연결 요청에 대한 Request Type 플래그 "handover"를 지원한다고 알려야 한다.

This indication is valid for the entire Registered PLMN and for PLMNs equivalent to the Registered PLMN. The same indication is provided to all UEs served by the same PLMN. UEs that operate in interworking without N26 may use this indication to decide whether to register early in the target system. UEs that only support single registration mode may use this indication as described in clause 5.17.2.3.2. UE that support dual registration mode uses this indication as described in clause 5.17.2.3.3.

이 표시 (Request type flag “Handover” 를 지원한다는 표시)는 전체 Registered PLMN Registered PLMN과 동일한 (equivalent) PLMN에 유효. 동일한 표시는 동일한 PLMN에 의해 ​​서비스되는 모든 UE들에게 제공된다. N26 미 사용 상호 연동 동작 가능한 UE 이 표시를 사용하여 target 시스템에 먼저 등록할 것인지 결정할 수 있다. 단일 등록 모드만을 지원하는 UE 5.17.2.3.2 절에 설명된대로 이 표시를 사용할 수 있다. 이중 등록 모드를 지원하는 UE 5.17.2.3.3 절에 설명 된대로 이 표시를 사용.

Interworking procedures without N26 interface use the following two features:

N26 미 사용 연동 절차에는 다음 두 가지 기능을 사용한다.:

1.      When UE performs Initial Attach in EPC (with or without "Handover" indication in PDN CONNECTIVITY Request message) and indicates that it is moving from 5GC, the MME does not include "initial attach" indicator to the HSS+UDM. This results in HSS+UDM not cancelling the registration of AMF, if any.

1. UE EPC에서 Initial Attach (PDN CONNECTIVITY 요청 메시지에 "Handover" 표시를 포함하거나, 포함하지 않는 경우 모두)를 수행하면서, 해당 단말이 5GC로부터 (EPC) 이동 중임을 나타낼 경우, MME HSS+UDM "initial attach"라는 표시를 포함하지 않도록 하여, HSS+UDM(기존) AMF로의 등록을 취소하지 않도록 한다.

2.  When UE performs Initial Registration in 5GC and indicates that it is moving from EPC, the AMF does not include "initial attach" indicator to the HSS+UDM. This results in HSS+UDM not cancelling the registration of MME, if any.

2. UE 5GC에서 초기 등록을 수행하고 EPC로부터 이동 중임을 나타낼 경우, AMF HSS+UDM "initial attach"라는 표시를 포함하지 않도록 하여, HSS+UDM(기존) MME로의 등록을 취소하지 않도록 한다.

To support mobility both for single and dual registration mode UEs, the following also are supported by the network:

단일 및 이중 등록 모드 UE 모두에 대한 이동성을 지원하기 위해, 다음의 동작 또한 네트워크에 의해 지원돼야 한다. :

3.      When PDU Session are created in 5GC, the PGW-C+SMF updates its information along with DNN in the HSS+UDM.

3. 5GC에서 PDU 세션이 생성되면, PGW-C+SMF HSS+UDM DNN 및 관련 정보를 업데이트.

4.  The HSS+UDM provides the information about dynamically allocated PGW-C+SMF and APN/DNN information to the target CN network.

4. HSS+UDM은 동적으로 할당된 PGW-C+SMF APN/DNN 정보를 대상 CN 네트워크에 제공.

5.  When PDN connections are created in EPC, the MME stores the PGW-C+SMF and APN information in the HSS+UDM.

5. EPC에서 PDN connection이 생성되면, MME PGW-C+SMF APN 정보를 HSS+UDM에 저장.

NOTE 2:  Items 3, 4 and 5 are also supported in networks that support interworking with N26 procedures. This enables a VPLMN that does not deploy N26 interface to provide IP address preservation to roamed-in single-registration mode UEs from a HPLMN that only supports interworking with N26 procedures.

2 : 항목 3, 4 5 N26 사용 연동 절차를 지원하는 네트워크에서도 지원. 이는 N26 인터페이스를 이용하지 않는 VPLMN에서 N26 사용 연동 절차만 지원하는 HPLMN으로부터 로밍된 단일 등록 모드 UEIP 주소를 유지할 수 있게 한다.

When the network serving the UE supports 5GS-EPS interworking procedures without N26 interface, the SMF shall not provide the UEs with mapped target system parameters of the target system when UE is in the source network.

UE를 서비스하는 네트워크가 N26 미 사용 5GS-EPS 연동 절차를 지원할 때, SMFtarget 시스템 매핑된 target 시스템 파라미터 UE가 소스 네트워크에 있는 동안 제공해서는 안된다.

When an AMF in a serving PLMN that does not support 5GS-EPS interworking procedures with N26 interface receives a request to allocate an EBI(s) for a QoS Flow(s) from a PGW-C+SMF, it shall not provide the EBI(s) but reject the EBI allocation request with a specific rejection cause. This is considered an explicit indication by SMF that 5GS-EPS interworking procedures with N26 interface are not supported in the serving PLMN.

N26 인터페이스 사용 5GS-EPS 연동 절차를 지원하지 않는 서빙 PLMN AMF PGW-C+SMF로부터 QoS Flow위한 EBI ()를 할당하라는 요청을 수신하면, EBI를 제공하지 말고 특정한 거절 사유로 EBI 할당 요청을 거절해야 한다. 이는 서빙 PLMN에서 N26 인터페이스를 사용하는 5GS-EPS 연동 절차가 지원되지 않는다는 SMF의 명시적인 표시로 간주.

A UE that operates in dual registration mode ignores any received mapped target system parameters (e.g. QoS parameters, bearer IDs/QFI, PDU Session ID, etc.).

이중 등록 모드로 동작하는 UE수신한 매핑된 target 시스템 파라미터(예를 들어, QoS 파라미터, 베어러 ID / QFI, PDU 세션 ID )를 모두 무시한다.

5.17.2.3.2            Mobility for UEs in single-registration mode

When the UE supports single-registration mode and network supports interworking procedure without N26 interface:

UE가 단일 등록 모드를 지원하고 네트워크가 N26 인터페이스를 미 사용하는 연동 절차를 지원할 때 :

-    For mobility from 5GC to EPC, the UE with at least one PDU Session established in 5GC may either:

- 5GC에서 EPC 로의 이동성을 위해, 5GC에서 설정된 하나 이상의 PDU 세션을 가진 UE는 다음 중 하나를 수행 할 수 있. :

-    if supported and if it has received the network indication that interworking without N26 is supported, perform Attach in EPC with a native EPS GUTI, if available, otherwise with IMSI with Request type "Handover" in PDN CONNECTIVITY Request message (TS 23.401 [26], clause 5.3.2.1) and indicating that the UE is moving from 5GC and subsequently moves all its other PDU Session using the UE requested PDN connectivity establishment procedure with Request Type "handover" flag (TS 23.401 [26] clause 5.10.2), or.

- (UE가 해당 동작을) 지원하고, N26미사용 연동이 지원된다는 표시 네트워크 표시를 수신 한 경우, 가능하다면 고유 EPS GUTI를 사용하, 그렇지 않으면 IMSIPDN CONNECTIVITY 요청 메시지에 Request Type “Handover” 를 사용하여 (TS 23.401[26], 5.3.2.1) EPC에서 Attach를 수행하고, UE5GC에서 이동하고 있음을 알려주고, 이후 모든 나머지 PDU Session 에 대해 Request Type “Handover” 를 포함한 UE requested PDN connectivity 수립 절차 (TS 23.401 [26] 5.10.2) 를 통해 이동하거나,

-    perform TAU with 4G-GUTI mapped from 5G-GUTI sent as old Native GUTI (TS 23.401 [26], clause 5.3.3) indicating that it is moving from 5GC, in which case the MME instructs the UE to re-attach. IP address preservation is not provided in this case.

- 이전 Native GUTI 로 전송 된 5G-GUTI에서 매핑 된 4G-GUTI TAU를 수행(TS 23.401 [26], 5.3.3 ) 하여 (해당 단말이) 5GC로부터 이동중임을 나타낸다. 이 경우 MMU UEre-attach 하도록 지시. 이 경우 IP 주소 유지 동작은 제공되지 않는다.

-    for the first TAU after 5GC initial Registration, the UE and MME for the handling of UE Radio Capabilities follow the procedures as defined in TS 23.401 [26] clause 5.11.2 for first TAU after GERAN/UTRAN Attach.

- 5GC 초기 등록 이후의 첫 번째 TAU , UE MMETS 23.401 [26]5.11.2 절에 정의된 GERAN/UTRAN Attach 후 첫 번째 TAU절차를 따라 UE Radio Capability 를 다루도록 한다.

NOTE 1:  The first PDN connection may be established during the E-UTRAN Initial Attach procedure (see TS 23.401 [26]).

1 : 첫 번째 PDN connection E-UTRAN 초기 접속 절차 (TS 23.401 [26] 참조) 중에 설정 될 수 있다.

NOTE 2:  At inter-PLMN mobility to a PLMN that is not an equivalent PLMN the UE always uses the TAU procedure.

2 : Equivalent PLMN이 아닌 PLMN 으로의 inter-PLMN 이동성에서 UE는 항상 TAU 절차를 사용한다.

-    For mobility from 5GC to EPC, the UE with no PDU Session established in 5GC

- 5GC에서 EPC 로의 이동성을 위해 PDU 세션이 5GC (접속한) UE

-    performs Attach in EPC (TS 23.401 [26], clause 5.3.2.1) indicating that the UE is moving from 5GC.

- UE 5GC에서 이동 중임을 나타내는 EPC 에서 Attach절차 (TS 23.401 [26], 5.3.2.1 )를 수행.

-    For mobility from EPC to 5GC, the UE performs Registration of type "mobility registration update" in 5GC with 5G-GUTI mapped from EPS GUTI and a native 5G-GUTI, if available, as Additional GUTI and indicating that the UE is moving from EPC. In this case, the AMF determines that old node is an MME, but proceeds as if the Registration is of type "initial registration". The UE may either:

- EPC에서 5GC 로의 이동성을 위해, UE EPS GUTI로부터 매핑 된 5G-GUTI, 이용 가능한 경우 추가 GUTI로서 네이티브 5G-GUTI를 사용하여 5GC에서 "mobility registration update" 유형으로 5GC등록을 수행하여 UEEPC에서 이동하고 있음을 나타낸다. 이 경우, AMF이전 노드가 MME 인 것으로 판단하되, "initial registration"유형인 것처럼 등록을 진행한다. (이 때,) UE는 다음 중 하나를 수행할 수 있다. :

-    if supported and if it has received the network indication "interworking without N26 supported", move all its PDN connections from EPC using the UE initiated PDU Session Establishment procedure with "Existing PDU Sessions" flag (TS 23.502 [3], clause 4.3.2.2.1), or

- (UE 가 해당 동작을) 지원, 네트워크로부터 “N26 미 사용 연동 동작을 지원한다는 indication 을 받은 경우,  "Existing PDU Sessions" 플래그를 포함한 UE initiated PDU 세션 설정 절차(TS 23.502 [3], 4.3.2.2.1 )를 사용하여 EPC에서 모든 해당 단말의 PDN connection을 이동하거나,

-    re-establish PDU Sessions corresponding to the PDN connections that it had in EPS. IP address preservation is not provided in this case.

- EPS서 가지고 있던 PDN connection에 해당하는 PDU 세션을 다시 설정한다. 이 경우 IP 주소 유지 동작은 제공되지 않는다.

NOTE 3:  The additional native 5G-GUTI enables the AMF to find the UE's 5G security context (if available).

3 : 추가적인 고유 5G-GUTIAMFUE 5G 보안 컨텍스트 (사용 가능한 경우)를 찾을 수 있도록 한다.

NOTE 4:  When single-registration mode UE uses interworking procedures without N26, the registration states during the transition period (e.g. while UE is transferring all PDU Sessions / PDN Connections on the target side) are defined in Stage 3 specifications.

4 : 단일 등록 모드 UE N26미 사용 연동 절차를 수행할 때, 전환 기간 (예를 들어, UEtarget 측의 모든 PDU 세션 / PDN 접속을 전송하는 동안) 동안의 등록 상태(registration states)Stage 3 규격에서 정의된다.

5.17.2.3.3            Mobility for UEs in dual-registration mode

To support mobility in dual-registration mode, the support of N26 interface between AMF in 5GC and MME in EPC is not required. A UE that supports dual registration mode may operate in this mode when it receives an indication from the network that interworking without N26 is supported.

이중 등록 모드에서 이동성을 지원하기 위해 5GC AMF EPC MME 간의 N26 인터페이스 지원은 필요하지 않다. 이중 등록 모드를 지원하는 UE는 네트워크로부터 N26미 사용 연동 동작을 지원한다는 표시를 수신할 때 이 모드로 동작 할 수 있다.

For UE operating in dual-registration mode the following principles apply for PDU Session transfer from 5GC to EPC:

이중 등록 모드로 동작하는 UE 경우, 5GC에서 EPC 로의 PDU 세션 전송에 다음 원칙을 적용한다.

-    UE operating in Dual Registration mode may register in EPC ahead of any PDU Session transfer using the Attach procedure indicating that the UE is moving from 5GC without establishing a PDN Connection in EPC if the EPC supports EPS Attach without PDN Connectivity as defined in TS 23.401 [26]. Support for EPS Attach without PDN Connectivity is mandatory for UE supporting dual-registration procedures.

- 이중 등록 모드로 동작하는 UE, TS 23.401 [26] 정의된 바와 같이, EPC EPS Attach without PDN Connectivity 지원할 경우, EPC PDN Connection 설정하지 않고 5GC에서 이동하고 있음을 나타내는 attach 절차를 사용하여 PDU 세션 transfer 이전에 (없이?) EPC 등록 있다. 이중 등록 절차를 지원하는 UE EPS Attach without PDN Connectivity지원해야 한다.

NOTE 1:  Before attempting early registration in EPC the UE needs to check whether EPC supports EPS Attach without PDN Connectivity by reading the related SIB in the target cell.

1 : EPC에서 조기 등록을 시도하기 전에, UE target 셀에서 관련 SIB 읽어서 EPC EPS Attach without PDN Connectivity지원하는지 여부를 확인 필요가 있다.

-    UE performs PDU Session transfer from 5GC to EPC using the UE initiated PDN connection establishment procedure with "handover" indication in the PDN Connection Request message (TS 23.401 [26], clause 5.10.2).

- UE PDN connection 요청 메시지 (TS 23.401 [26], 5.10.2 )에서 "handover" 표시를 포함한 UE initiated PDN connection 설정 절차를 사용하여 5GC에서 EPC PDU 세션 전송을 수행한다.

-    If the UE has not registered with EPC ahead of the PDU Session transfer, the UE can perform Attach in EPC with "handover" indication in the PDN Connection Request message (TS 23.401 [26], clause 5.3.2.1).

- UE PDU 세션 전송 이전에 EPC 등록하지 않은 경우, UE PDN Connection 요청 메시지에 “handover”표시를 포함하여 EPCAttach 수행 있다(TS 23.401 [26], 5.3.2.1 ).

-    UE may selectively transfer certain PDU Sessions to EPC, while keeping other PDU Sessions in 5GC.

- UE 5GC에서 다른 PDU 세션을 유지하면서 특정 PDU 세션을 EPC 선택적으로 전송할 있다.

-    UE may maintain the registration up to date in both 5GC and EPC by re-registering periodically in both systems. If the registration in either 5GC or EPC times out (e.g. upon mobile reachable timer expiry), the corresponding network starts an implicit detach timer.

- UE 시스템에 주기적으로 등록함으로써 5GC EPC 모두에서 최신 등록 상태를 유지할 있다. 만약 5GC 또는 EPC 어느 하나에서 등록이 만료되면 (예를 들어, 모바일 도달 가능 타이머 만료 시), 해당 네트워크는 암시 분리 타이머를 시작한다.

NOTE 2:  Whether UE transfers some or all PDU Sessions on the EPC side and whether it maintains the registration up to date in both EPC and 5GC can depend on UE capabilities that are implementation dependent. The information for determining which PDU Sessions are transferred on EPC side and the triggers can be pre-configured in the UE and are not specified in this Release of the specification. The UE does not know before-hand, i.e. before trying to move a given PDU session to EPC, whether that PDU session can be transferred to EPC.

2 : UE EPC 측에서 일부 또는 모든 PDU 세션을 전송하는지, EPC 5GC에서 최신으로 등록을 유지하는지 여부는 구현에 따라 달라질 수 있는 UE capability 에 달려 있다. 어떤 PDU 세션이 EPC 측에서 전송되고, 트리거가 UE에서 사전 구성 있는지를 결정하기 위한 정보는 본 규격의 이번 릴리스에서는 정의되지 않는다. UE 사전에, 예를 들어 주어진 PDU 세션을 EPC 이동하기 전에, PDU 세션이 EPC 전송 있는지 여부를 알지 못한다.

For UE operating in dual-registration mode the following principles apply for PDN connection transfer from EPC to 5GC:

이중 등록 모드에서 동작하는 UE 경우 EPC에서 5GC 로의 PDN connection 전송에 다음 원칙이 적용된다.

-    UE operating in Dual Registration mode may register in 5GC ahead of any PDN connection transfer using the Registration procedure indicating that the UE is moving from EPC (TS 23.502 [3], clause 4.2.2.2.2).

- 이중 등록 모드로 동작하는 UE UE EPC (TS 23.502 [3], 4.2.2.2.2 )에서 이동 중임을 나타내는 등록 절차를 사용하여 PDN 연결 이전에 5GC 등록 있다.

-    UE performs PDN connection transfer from EPC to 5GC using the UE initiated PDU Session Establishment procedure with "Existing PDU Session" indication (TS 23.502 [3], clause 4.3.2.2.1).

- UE "Existing  PDU Session" 표시를 포함하는 UE initiated PDU 세션 설정 절차(TS 23.502 [3], 4.3.2.2.1 ) 사용하여 EPC에서 5GC 로의 PDN 연결 전송을 수행한다.

-    UE may selectively transfer certain PDN connections to 5GC, while keeping other PDN Connections in EPC.

- UE EPC에서 다른 PDN 연결을 유지하면서 특정 PDN 연결을 5GC 선택적으로 전송할 있다.

-    UE may maintain the registration up to date in both EPC and 5GC by re-registering periodically in both systems. If the registration in either EPC or 5GC times out (e.g. upon mobile reachable timer expiry), the corresponding network starts an implicit detach timer.

- UE 시스템에서 주기적으로 등록함으로써 EPC 5GC에서 최신 등록 상태를 유지할 있다. EPC 또는 5GC 어느 하나에 등록이 만료되면 ( : 모바일 도달 가능 타이머 만료 시) 해당 네트워크가 암시적 분리 타이머를 시작한다.

NOTE 3:  Whether UE transfers some or all PDN connections on the 5GC side and whether it maintains the registration up to date in both 5GC and EPC can depend on UE capabilities that are implementation dependent. The information for determining which PDN connections are transferred on 5GC side and the triggers can be pre-configured in the UE and are not specified in this Release of the specification. The UE does not know before-hand, i.e. before trying to move a given PDN connection to 5GC, whether that PDN connection can be transferred to 5GC.

3 : UE 5GC 측의 일부 또는 모든 PDN 연결을 전송하는지 여부와 5GC EPC 모두에서 최신으로 등록을 유지하는지 여부는 구현에 따라 달라질 수 있는 UE capability 에 달려 있다. 어떤 PDN 연결이 5GC 측에서 전송되고 트리거가 UE에서 사전 구성 있는지를 결정하기 위한 정보는 본 규격의 이번 릴리스에서는 정의되지 않는다. UE 사전에, 예를 들어 주어진 PDN 접속을 5GC 이동하기 전에, PDN 접속이 5GC 전송될 있는지 여부를 알지 못한다.

NOTE 4:  If EPC does not support EPS Attach without PDN Connectivity the MME detaches the UE when the last PDN connection is released by the PGW as described in TS 23.401 [26] clause 5.4.4.1 (in relation to transfer of the last PDN connection to non-3GPP access).

4 : EPC  EPS Attach without PDN Connectivity지원하지 않으면 TS 23.401 [5.4] 5.4.4.1 (마지막 PDN 연결을 non-3GPP 액세스로 전송하는 것과 관련한 부분)에서 설명한대로 PGW 의해 ​​마지막 PDN 연결이 해제 MME UE detach 시킨다.

When sending a control plane request for MT services (e.g. MT SMS) the network routes it via either the EPC or the 5GC. In absence of UE response, the network should attempt routing the control plane request via the other system.

MT 서비스 ( : MT SMS)에 대한 제어 평면 요청을 보낼 때 네트워크는 EPC 또는 5GC중 하나를 통해 라우팅. UE에서 응답이 없는 경우, 네트워크는 나머지 다른 시스템을 통해 제어 평면 요청을 라우팅하도록 시도해야 한다.

NOTE 5:  The choice of the system through which the network attempts to deliver the control plane request first is left to network configuration.

5 : 어떤 네트워크로 제어 평면 요청을 먼저 전달할지는 네트워크 구성에 달려 있다.

5.17.2.3.4            Redirection for UEs in connected state

When the UE supports single-registration mode or dual-registration mode without N26 interface:

UE N26 인터페이스 없이 단일 등록 모드 또는 이중 등록 모드를 지원할 때 :

-    If the UE is in CM-CONNECTED state in 5GC, the NG-RAN may perform RRC Connection Release with Redirection to E-UTRAN based on certain criteria (e.g. based on local configuration in NG-RAN, or triggered by the AMF upon receiving Handover Request message from NG-RAN).

- UE 5GC에서 CM-CONNECTED 상태에 있는 경우, NG-RAN은 특정 기준 ( : NG-RAN의 로컬 구성에 기반하거나 NG-RAN으로부터 Handover Request 메시지를 수신했을 때 AMF에 의해 트리거 됨)에 기반하여 E-UTRAN으로의 리다이렉션으로 RRC 연결 해제를 수행 할 수 있다.

-    If the UE is in ECM-CONNECTED state in EPC, the E-UTRAN may perform RRC Connection release with redirection to NG-RAN based on certain criteria (e.g. based on local configuration in E-UTRAN, or triggered by the MME upon receiving handover request from E-UTRAN).

- UE EPC에서 ECM-CONNECTED 상태에 있는 경우, E-UTRAN은 특정 기준 (: E-UTRAN의 로컬 구성에 기반하거나, E-UTRAN으로부터의 Handover request 를 수신 시 MME에 의해 트리거 됨)에 기초하여 NG-RAN 으로의 리다이렉션으로 RRC 연결 해제를 수행 할 수 있다.

5.17.2.4        Mobility between 5GS and GERAN/UTRAN

IP address preservation upon mobility between 5GS and GERAN/UTRAN is not supported.

5GS GERAN/UTRAN 간의 이동 시 IP 주소는 유지 기능은 지원되지 않는다.

Upon mobility from 5GS to GERAN/UTRAN (e.g. upon leaving NG-RAN coverage) the UE shall perform the A/Gb mode GPRS Attach procedure or Iu mode GPRS Attach procedure (see TS 23.060 [56]).

UE 5GS에서 GERAN/UTRAN으로 이동할 때 ( : NG-RAN 커버리지를 벗어날 때) A / Gb 모드 GPRS 부착 절차 또는 Iu 모드 GPRS 부착 절차를 수행해야 한다 (TS 23.060 [56] 참조).

Upon mobility from GERAN/UTRAN to 5GS (e.g. upon selecting an NG-RAN cell) the UE shall perform the Registration procedure of "initial registration" type as described in TS 23.502 [3]. The UE shall indicate a 5G-GUTI as UE identity in the Registration procedure if it has a stored valid native 5G-GUTI (e.g. from an earlier registration in the 5G System). Otherwise the UE shall indicate a SUCI.

UE GERAN/UTRAN에서 5GS로 이동할 때 ( : NG-RAN 셀 선택 시) TS 23.502 [3]에서 설명한대로 “Initial registration"유형의 등록 절차를 수행해야 한다. UE (예를 들어, 5G 시스템의 초기 등록으로부터) 저장된 유효한 5G-GUTI를 가지고 있다면, 등록 절차에서 UE 식별 정보로서 5G-GUTI를 표시해야 한다. 그렇지 않으면 UE SUCI를 표시해야 한다.

If a UE in MICO mode moves to GERAN/UTRAN and any of the triggers defined in clause 5.4.1.3 occur, then the UE shall locally disable MICO mode and perform the A/Gb mode GPRS Attach procedure or Iu mode GPRS Attach procedure (see TS 23.060 [56]). The UE can renegotiate MICO when it returns to 5GS during (re-)registration procedure.

MICO 모드에 있는 UE GERAN/UTRAN으로 이동할 때 5.4.1.3 절에서 정의 된 트리거가 발생하면, UE MICO 모드를 국지적으로 비활성화하고 A/Gb 모드 GPRS 부착 절차 또는 Iu 모드 GPRS 부착 절차를 수행해야 한다. (TS 23.060 [56] 참조). UE는 재 등록 과정에서 5GS로 복귀할 때 MICO를 재협상 할 수 있다.

5.17.3     Interworking with EPC in presence of Non-3GPP PDU Sessions

When a UE is simultaneously connected to the 5GC over a 3GPP access and a non-3GPP access, it may have PDU Sessions associated with 3GPP access and PDU Sessions associated with non-3GPP access. When inter-system handover is performed for PDU Sessions associated with 3GPP access, the PDU Sessions associated with non-3GPP access remain anchored in 5GC.

UE 3GPP 액세스 Non-3GPP 액세스를 통해 5GC 동시에 접속되는 경우, UE Non-3GPP 액세스와 관련된 3GPP 액세스 PDU 세션과 관련된 PDU 세션을 가질 있다. 시스템 핸드 오버가 3GPP 액세스와 관련된 PDU 세션에 대해 수행 , Non-3GPP 액세스와 연관된 PDU 세션은 5GC 고정되어 있다.

5.17.4     Network sharing support and interworking between EPS and 5GS

The detailed description for supporting network sharing and interworking between EPS and 5GS is described in clauses 4.11.1.2.1, 4.11.1.2.2, 4.11.1.3.2 and 4.11.1.3.3 of TS 23.502 [3].

EPS 5GS 간의 네트워크 공유 및 연동을 지원하기 위한 자세한 설명은 TS 23.502 [3] 4.11.1.2.1 , 4.11.1.2.2 , 4.11.1.3.2 절 및 4.11.1.3.3 절에 설명되어 있다.